GS690 6″ x 9″ PREMIUM GRADE AUTOMOTIVE WOOFER/MIDRANGE LOUDSPEAKER
Designed to be used in two- or three-way systems, the GS690 includes a non-resonant injection-molded ABS plastic and fiberglass vented basket. For a 2-Way system, use a GS10 tweeter and a GS610C crossover. You can also use the GS690 with a GS42 and an active crossover, or with a GS10, GS40 and GS410C with an active crossover between the GS690 and GS40.
The 1" copper voice coil wound on a Kapton® former provides high power handling. A parabolic propylene cone ensures long-term reliability and provides the right compromise between compliance and stiffness for flatter high frequency response. The ferrite motor includes a neodymium bucking magnet atop the pole piece for increased motor strength and sensitivity. Terminals are secured by a small PC board integrated into the inside of the basket.
- Nominal Impedance: 4Ω
- RMS Power Handling: 100 W
- Peak Power Handling: 300 W
- Frequency Response (-3 dB): 42 Hz – 5 kHz
- Sensitivity (2.83 V/1 M): 92 dB
- Recommended Amplifier RMS Power Range: 15 W – 100 W
- Recommended Low Pass Filter Frequency and Slope: ≤ 3.5 kHz, ≥ 12 dB/oct
G62 High Performance 6″ Coaxial Speaker
Featuring a 6-1/2" woofer with a polypropylene cone and rubber surround and a 1" fabric dome tweeter, the G62 is designed to make installation easy and to provide the market leading performance you've come to expect from Audiofrog.
The woofer's steel basket is shallow enough to fit nearly every factory-provided 6" location using the included multiadapter. The height of the tweeter above the surround edge has been minimized so that the G62 can be easily installed in factory locations under factory grilles.
Since 6" coaxials are most often mounted in the factory location at the bottom of the front and/or rear doors or in the package tray in the rear of a sedan, the frequency response has been designed to compliment those locations. At high frequencies, the output of the speaker rises to counteract the off-axis attenuation caused by the locations. The result is crisp and clear high frequencies even in the factory locations—a clear upgrade.
- Nominal Impedance: 4Ω
- RMS Power Handling: 50 W (with crossover)
- Peak Power Handling: 120 W (with crossover)
- Frequency Response:50 Hz – 20 kHz
- Sensitivity (2.83 V/1 M): 89 dB
- Recommended Amplifier RMS Power Range: 15 W – 75 W
- Dimensions:
- Cut-out Diameter: 132.5 mm (5-7/32")
- Overall Diameter: 158.2 mm (6-15/64″)
- Overall Diameter Including Mounting Tabs: 166 mm (6-17/32″)
- Mounting Depth: 51.2 mm (2-1/64″)
- Mounting Height: 14.2 mm (9/16″)
Thiele and Small Parameters (woofer):
- Revc: 2.25 Ω
- Levc@1kHz: 0.13 mH
- Sd: 143.14 cm²
- Mmd: 11.8 g
- Mms: 12.37 g
- Cms: 317 µM/N
- Vas: 9.12 liters
- Fs: 80.39 Hz
- BL: 3.91 TM
- Qms: 7.89
- Qes: .92
- Qts: 0.83
- Xmax (1-way linear): 4 mm (5/32")
- Basket Displacement: 0.24 liters (0.008 ft³)
GS25 2.5″ (65mm) Premium Grade Full Range Automotive Loudspeaker
Designed as a drop-in upgrade in many GM, Toyota and Mercedes vehicles, the GS25 is a full range speaker (200 Hz – 20 kHz) ideal when retention of the factory amplifier and equalization makes the most sense. In many premium systems in these cars the factory system includes crossover and EQ that make replacing the factory mid bass in the door and the factory full range with a standard component system with a passive crossover a big problem. GS25 to the rescue! Use the GS25 along with the GS60 or GS690 for an easy to install high performance upgrade.
The GS25 includes a single layer CCAL voice coil for low inductance and extended high frequency response. The neodymium motor also includes a copper cap over the polepiece to reduce distortion and to further extend the high frequency response. A bucking magnet atop the polepiece redirects magnetic energy into the magnetic gap to increase sensitivity. GS25 is a high end full range driver designed for easy installation.
The GS25 includes a steel basket with break off mounting tabs designed to fit a wide variety of Toyota, GM and Mercedes vehicles. For standard installation or for other cars for which no direct mount tabs are included, all of the tabs can be removed and the speaker can be mounted in a standard configuration.
Finally, for a GS level 3-way system with a DSP or active crossovers, use the GS25 with a GS10 tweeter and a GS60 or GS690 midbass driver.
Specifications:
Nominal Impedance: 4Ω
RMS Power Handling: 70 W (with recommended crossover)
Peak Power Handling: 150 W (with recommended crossover)
Frequency Response (-3 dB): 200 Hz – 20 kHz
Sensitivity (2.83 V/1 M): 87 dB
Recommended Amplifier RMS Power Range: 15 W – 75 W
Recommended High Pass Filter Frequency and Slope: ≥ 200 Hz, ≥ 12 dB/oct
GS10OE 1″ (25MM) PREMIUM GRADE AUTOMOTIVE TWEETER
- 1″ (25 mm) fabric dome
- 1″ (25 mm) voice coil on aluminum former
Ferrofluid-filled gap for superior heat dissipation and increased damping at resonance - Neodymium motor with copper pole piece cap
- Bucking magnet for increased sensitivity
- Reflection-absorbing and diffusing foam pad under diaphragm for smooth frequency response
- Screw terminals
- Industry-leading mounting kit included
Hex screws and tools included - Designed for use with GS40, GS60, GS410C and GS610C
Specifications:
- Nominal Impedance: 4 Ω
- RMS Power Handling: 70 W (with recommended crossover)
- Peak Power Handling: 200 W (with recommended crossover)
- Frequency Response: 1.8 kHz – 20 kHz
- Sensitivity (2.83V / 1M): 92 dB
- Recommended Amplifier RMS Power Range: 15 W – 75 W
- Recommended High Pass Filter Frequency and Slope: ≥ 3.5 kHz, ≥ 12 dB/oct
